BENSHAW ENHANCED KEYPAD Instrukcja Użytkownika Strona 89
- Strona / 222
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
P8 Ramp Time 1 QST 08, CFN 02
LED Display LCD Display
Range 0 – 300 seconds (Default 15)
Description The Ramp Time 1 parameter is the time it takes for the starter to allow the current, voltage, torque or power
(depending on the start mode) to go from its initial to the maximum value. To make the motor accelerate
faster, decrease the ramp time. To make the motor accelerate slower, increase the ramp time.
A typical ramp time setting is from 15 to 30 seconds.
If the ramp time expires before the motor reaches full speed, the starter maintains the maximum current level
until either the motor reaches full speed, the UTS timer expires, or the motor thermal overload trips.
z NOTE: Setting the ramp time to a specific value does not necessarily mean that the motor will take this
time to accelerate to full speed. The motor and load may achieve full speed before the ramp time expires if
the application does not require the set ramp time and maximum current to reach full speed. Alternatively, the
motor and load may take longer than the set ramp time to achieve full speed.
See Also Initial Current 1 (P6 / QST 06) parameter on page 79.
Maximum Current 1 (P7 / QST 07) parameter on page 80.
Up To Speed Time (P9 / QST 09) parameter on page 82.
Start Mode (P10 / CFN 01) parameter on page 83.
Kick Level 1 (P13 / CFN 10) parameter on page 86.
Kick Time 1 (P14 / CFN 11) parameter on page 86.
Theory of Operation section 7.3.1, Current Ramp Settings, Ramps and Times on page 140.
81
6 - PARAMETER DESCRIPTION
CFN: Ramp Time 1
02 15 sec
QST: Ramp Time 1
08 15 sec
- RediStart 1
- Important Reader Notice 2
- SAFETY PRECAUTIONS 3
- TABLE OF CONTENTS 4
- 1 Introduction 9
- 1 - INTRODUCTION 10
- RB2-1-S-052A-12C 14
- 2 Technical Specifications 17
- 2 - TECHNICAL SPECIFICATIONS 18
- 3 Installation 35
- 3 - INSTALLATION 36
- BIPC-300055-01 40
- 120VAC LIVE 48
- 120VAC NEUTRAL 48
- 4 Keypad Operation 55
- PARAM DOWN UP ENTERRESET 56
- 4 - KEYPAD OPERATION 57
- 5 Parameter Groups 67
- 5 - PARAMETER GROUPS 68
- 6 Parameter Description 81
- Local Source 86
- · Keypad 86
- Local/Remote Bit 86
- P48, P49, P50 86
- 6 - PARAMETER DESCRIPTION 100
- % Current 108
- 7 Theory of Operation 139
- 7 - THEORY OF OPERATION 140
- Derating Factor 142
- Ramp Profile 2 156
- Ramp Profile 1 156
- IMPORTANT 180
- Troubleshooting 181
- & Maintenance 181
- Safety Precautions 182
- Preventative Maintenance 182
- control 183
- . Initial current to low 184
- Condition 185
- Fault Code Table 188
- SCR Testing 195
- Built-In Self Test Functions 196
- BIST Mode 197
- Tests completed 197
- SCR Replacement 199
- Appendices 201
- APPENDIX A - ALARM CODES 202
- APPENDIX B - FAULT CODES 204
- APPENDIX C - SPARE PARTS 205
- EU DECLARATION OF CONFORMITY 206
- APPENDIX EMODBUS REGISTER MAP 207
- 0 – 99 % 211
- 214
- Diagnostics 214
- APPENDIX FPARAMETER TABLES 215
- APPENDIX F - PARAMETER TABLES 216
- Publication History; 221
Panasonic RP HC50 manuály
Uživatelské manuály a uživatelské příručky pro Sluchátka Panasonic RP HC50.
Poskytujeme 1 manuály pdf Panasonic RP HC50 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji